Check polarity of battery posts. Do not operate the battery charger near flammable liquids or in gaseous or explosive atmospheres. When the unit is properly connected, press the charge/voltage button to start the charging process. Shop products from small business brands sold in Amazons store. To reduce the risk of injury: Unplug the battery charger when not in use. Insert the AC plug of the battery charger into a (powered) standard North American 120 volt 60Hz outlet. Stay alert. You can trust these EverStart Batteries to perform as expected in your vehicle. PLEASE REFER TO THE INSTRUCTION MANUAL AND YOUR VEHICLE'S USER'S MANUAL BEFORE USE. Ensure that all installation and operating instructions and safety precautions are understood and carefully followed by anyone mounting or using the battery charger. Do not operate this equipment when you are tired or impaired. By following these simple steps, you will be able to keep your flashlight running at its best! Dont use the battery charger in damp or wet locations. If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturers option. www.Baccusglobal.com 1-877-571-2391. Connect to heavy gauge metal part of the frame or engine block. Be careful when using a knife you may cut yourself if youre not careful. Everstart Maxx 4 Amp Waterproof 12v Automotive and Marine Battery Charger (BC4WE) 39 $86.23 Maxx J5CPDE Jump Starter, Power Station, 1200 Peak Battery Amps with 500W Inverter and 120 PSI Compressor $80.00 1000 Peak Amp Power Station with Jump Starter, 120 PSI Compressor, Wireless Phone Charging and USB Ports 42 $8.99 Pressing the alternator check button or the battery recondition button will have no effect. Q: Why cant a dead battery be charged by my EverStart Maxx BC4WE 4 Amp Battery Charger? Carefully connect the NEGATIVE (BLACK) charger clamp to the free end of the battery cable connected to the negative terminal. Insert the double barrel tip of the battery clamp cable into the units Double Barrel Charger Connector (male-to-female and female-to-male). Have plenty of fresh water and soap nearby in case battery acid contacts skin. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. Connect to a heavy gauge metal part of the frame or engine block. 621 NW 53rd St., Suite 450, Boca Raton, FL 33487 www.Baccusglobal.com 1-877-571-2391, Download EverStart Maxx BC4WE 4A Waterproof Battery Charger Manual. Be extra cautious to avoid dropping a metal tool onto the battery. This charger is not designed for use with every make, manufacturer or model of engine. If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes and get medical attention immediately. Opening the battery charger will void the manufacturers warranty. After making sure that all connections are secure, place the flashlight in its charger cradle while balancing it with one hand on the front and one at the back. A: The problem of plugged in, not charging may be caused by a damaged cord. Check polarity of battery posts. The unit is for charging a 12 volt battery only. The final current level and the peak charging voltage when this current is flowing are the two factors that determine whether a battery is fully charged. Grab it and feel for any bulging or other irregularities. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Ensure that all installation, operating instructions and safety precautions are understood and observed; then follow the steps outlined in the appropriate section (Charging a battery Installed in a Vehicle or Charging a Battery That has been Removed from a Vehicle). Everstart Maxx BC50BE 15 Amp Automotive Battery Charger Everstart Maxx BC50BE 15 Amp Automotive Battery Charger QUICK START GUIDE BC50BE THIS QUICK START GUIDE IS NOT A SUBSTITUTE FOR THE INSTRUCTION MANUAL. Determine voltage of the battery to be charged by referring to the vehicle manual. Clean the unit casing and cords (as necessary) with a dry cloth. Connect NEGATIVE (BLACK) clamp to vehicle chassis or engine block away from battery. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor. It is hard to believe that inexpensive batteries can perform better than those that cost twice as much, but their efficiency is proved by the latest Consumer Reports tests. The following table shows the correct size to use depending on cord length and nameplate ampere rating. An extension cord should not be used unless absolutely necessary. To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. To stop charging, press the charge button. Attach a 24-inch (minimum length) AWG #6 insulated battery cable to the Negative battery post (marked NEG, N, ). The unit is for charging a 12 volt battery only. The alternator check indicates potential alternator issues. If in doubt, use the next heavier gauge. Have plenty of fresh water and soap nearby in case battery acid contacts skin. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The most popular AGM (absorbed glass mat) battery models are EverStart Plus and EverStart Maxx. Do not hang the charger from or attach the charger to any electrical wires or anything that it is not secure. My passion is helping people see just how beneficial proper lighting can be for their lives. Use of accessories and attachments: The use of any accessory or attachment not recommended by manufacturer for use with this battery charger could be hazardous. Recommended accessories for use with this unit may be available from the manufacturer. NOTE: this unit is a high-frequency smart charger. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. Locate charger as far away from battery as cables permit. Do not attach or hang anything additional to the charger or risk of breakage may occur. A: 5 hours following the completion of the batterys external or internal charging (by charger or alternator), or following at least an hour of discharge. Store the unit in a clean, dry, cool place when not in use. Quick start guide for EverStart Maxx. Do not over-tighten as this will damage the housing. Return to manufacturer for replacement of worn or defective parts immediately. The positive end of the battery should be facing up, and the negative end of the battery should be facing down. Everstart Maxx Battery Charger User Manual - Everstart Maxx Jump Starter And Power Station 1200 Peak Battery Amps With 500w Inverter And 120 Psi Compressor J5cpde Dxoffersmall Com Dxoffersmall Com In California -. Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 1-877-571-2391. Never allow battery acid to come in contact with this unit. Insert the AC plug of the battery charger into a (powered) standard North American 120 volt 60Hz outlet. EverStart Maxx BC4WE. Nintendo Switch Adjustable Charging Stand User Instructions, Westinghouse WVE612 Multifunction 8 Double Oven with AirFry User Manual, Nintendo Switch USB AC Adapter User Guide, Honeywell Single-Stage RTH2410 Programmable Thermostat Owner's Manual, WS-858 Wireless Karaoke Microphone User Manual, Onn 17LY80 Bluetooth In Ear Headphones User Manual, Westinghouse WVE915SCA Pyrolytic Oven with AirFry User Guide, Bose CineMate 15 Home Theater Speaker Owner's Guide, EverStart MAXX BC50BE 15 Amp Automotive Battery Charger, SPECIFIC SAFETY INSTRUCTIONS FOR POWER CORDS, SPECIFIC SAFETY INSTRUCTIONS FOR BATTERY CHARGERS, CHARGING A BATTERY INSTALLED IN A VEHICLE, CHARGING A BATTERY THAT HAS BEEN REMOVED FROM A VEHICLE, FAQS about EverStart MAXX BC50BE 15 Amp Automotive Battery Charger, Video for EverStart MAXX BC50BE 15 Amp Automotive Battery Charger, EverStart maxx EL224 600 Amp Lithium-ion Jump Starter, EverStart Maxx BC4WE 4 Amp Battery Charger, EverStart Maxx BC40BE 40 Amp Automotive Bench Battery Charger, https://manualsdock.com/wp-content/uploads/2022/12/617d1ec3-275c-4a18-9ff6-b73cff64ec4a_video_merchant_manual.mp4, EverStart MAXX PPS1CWE 1000 Amp Jump Starter. Always disconnect the AC plug from the AC outlet first before disconnecting the charger from the battery to be charged. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Recharging carefully is the greatest strategy to ensure that your car battery lasts a long time. 3. Connect NEGATIVE (BLACK) clamp to vehicle chassis or engine block away from battery. If negative post is grounded to chassis (as in most vehicles), see 5. Connect POSITIVE (RED) clamp to vehicle chassis or engine block away from battery. Philips Remote Control for Samsung Apple User Manual, Telstra NBN network using the Gen2 Smart Modem User Guide, EverStart maxx EL224 600 Amp Lithium-ion Jump Starter Owners Manual, EverStart MAXX PPS1CWE 1000 Amp Jump Starter Instructions Manual, EverStart SL097 Jump Starter Power Pack Manual. This charger is not designed for use with every make, manufacturer or model of engine. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. Consult the dealer or an experienced radio/TV technician for help. Ensure that unit is completely disconnected from battery and power source before cleaning. Be aware of first aid procedures in case of accidental contact with battery acid. The following table shows the correct size to use depending on cord length and nameplate ampere rating. It might spark or short-circuit the battery or another electrical part, and that may cause an explosion. Click the green button to print the entire article.To print the original version of the document - click the blue one. By following these simple steps, you can ensure that your Everstart Maxx flashlight is always ready. Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage. If it does not sense sufficient . Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If your flashlight has a spring, you can use pliers to attach the red wire easily. Dont abuse cord. Never allow battery acid to drip on charger. Consult the dealer or an experienced radio/TV technician for help. To maintain the operating condition and maximize the life of the charger cords, always coil them loosely for storage. Make sure your extension cord is in good condition. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. When the Charging/Charged LED lights solid, the charging process is complete. EverStart Maxx BC40BE Manual Questions? Check for damaged parts. Johnson Controls produces EverStart batteries. Do not attempt to defeat this safety feature. This device complies with part 15 of the FCC rules. Step 1: Set your multi meter at 20V. Do not open the battery charger there are no user-serviceable parts inside. Unplug the battery charger when not in use. The digital display shows 5 sec. indicating a 5-second countdown. Keep cord from heat, oil, and sharp edges. Q: How can you tell when an EverStart MAXX BC50BE 15 Amp Automotive Battery Charger for cars is done? The EverStart MAXX BC50BE 15 Amp Smart Battery Charger and Maintainer helps to charge and maintain 12V AGM, GEL and WET compatible batteries. When disconnecting charger, disconnect AC cord, and then remove the Terminals Rings from the battery posts. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Changes or modifications not approved by the party responsible for compliance could void users authority to operate the equipment. A: 5 hours following the completion of the batterys external or internal charging (by charger or alternator), or following at least an hour of discharge. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. WARNING BURST HAZARD: Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. 2. Check polarity of battery posts. This battery charger is designed so that it can be mounted on a flat surface. However, the performance wont be the same since these other types usually have just 2600 mAh of power. Return to manufacturer for replacement of worn or defective parts immediately. [3 Methods Explained], How to Change Light Bulb in Ge Monogram Refrigerator, How to Run a Light Bulb Off a Car Battery. FEATURES AC Power Cord Charging / Charged LED Reverse Polarity LED Battery Clamps Double Barrel Charger Connector (connects to terminal rings, clamps) Battery Terminal Rings Use the unit for charging/boosting a 12 volt battery only. With the Terminals Rings properly connected to the battery posts, connect the Terminal Ring connector with the units Double Barrel Charger Connector (male-to-female and female-to-male) and position it as far away from the battery as possible. Reorient or relocate the receiving antenna. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons. The new battery should have the same colors of wire like the old battery. Never carry home appliance by cord or yank it to disconnect from the receptacle. Review cautionary markings on this product and on engine. Keep children away. Call customer service hotline When disconnecting the charger, always do so in reverse sequence of connecting procedure and break first connection while as far away from battery as practical. Failure to follow all instructions listed below may result in electric shock, fire and/ or serious injury. If negative post is grounded to chassis (as in most vehicles), see 5. Do not operate this equipment when you are tired or impaired. During this period, pressing the battery voltage check button again will return the unit to charging mode. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The LCD screen will display the following to indicate the unit is analyzing the alternator: 2. Visit: EverStart maxx EL224 600 Amp Lithium-ion Jump Starter or EverStart SL097 Jump Starter, WARNING: Read and understand this instruction manual before using this unit. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor. If your flashlight has a built-in protection circuit, it may not allow you to charge the battery if its too low. After viewing product detail pages, look here to find an easy way to navigate back to pages you are interested in. Return it to the manufacturer for repair. AGM and lead acid batteries are both available in the EverStart series. A: The Everstart Maxx alternator typically needs 40.8 hours to completely charge a battery. ManualsDock also connects a growing community of active product owners with self-help and product knowledge, there are thousands of manuals from hundreds of big manufacturers. The EverStart Maxx Battery Charger is designed for use in emergency situations, such as the power going out. Ensure that all installation and operating instructions and safety precautions are understood and carefully followed by anyone mounting or using the battery charger. When disconnecting the charger, always do so in reverse sequence of connecting procedure and break first connection while as far away from battery as practical. Add distilled water in each cell until battery acid reaches level specified by battery manufacturer. If you dont have a voltmeter, you can use a battery tester to test the batterys voltage. Insert a new 18650 rechargeable Li-ion battery into the light. This equipment employs parts (switches, relays, etc.) Clean battery terminals, taking care to avoid getting corrosive material in the eyes. However, with the same battery, chargers with only 5 amps will require a full six hours. and then, at the flick of a switch, it can go from charging traditional 12V automotive systems in . The " everstart maxx 50 amp battery charger manual pdf " is a device that can charge batteries at high speed. These batteries may burst and cause injury to persons and damage property. Determine which post of the battery is grounded (connected) to the chassis. The use of any accessory not recommended for use with this appliance could be hazardous. These limits are designed to provide reasonable protection against harmful interference in a residential installation. To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. Check battery charger and components periodically for wear and tear without disassembling unit. Store the unit in a clean, dry, cool place when not in use. Keep children away. Read and understand this instruction manual before using this unit. Standard sealed lead acid battery charge characteristics for cycle service, where peak voltage may be higher and charging is intermittent. Insert the AC plug of the battery charger into a (powered) standard North American 120 volt 60Hz outlet. These limits are designed to provide reasonable protection against harmful interference in a residential installation. that produce arcs or sparks. Turning off the controls will not reduce this risk. Never operate charger in a closed-in area or restrict ventilation in any way. Do not allow clamps to be exposed to the elements for long periods of time; and never submerge them. A: Human error, such as not understanding how to use a car battery charger, using amp settings that are too high, or selecting the wrong voltage, can also result in overcharging your battery. The unit has a polarized plug (one blade is wider than the other) as a safety feature. Receptacles are available having built in GFCI protection and may be used for this measure of safety. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting, read the vehicle's owner's manual to confirm that external-starting assistance is suitable. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.\. Place the black wire back in its original position with both ends now attached to this metal plate. Note: A marine (boat) battery must be removed and charged on shore. Proof of purchase may be required by manufacturer. Connect the Positive (RED) battery clamp to the Positive battery post (marked POS, P, + or red). An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When disconnecting the battery charger, first unplug the AC cord, remove the clamp from the vehicle chassis, and then remove the clamp from the battery terminal. It is about six inches long and has a cylindrical shape. Ground fault circuit interrupter (GFCI) protection should be provided on the circuits or outlets to be used. This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product. TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: The housing of this unit is rated to IP67 dust-proof and waterproof standards. (2) Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Visit: EverStart MAXX BC50BE 15 Amp Automotive Battery Charger. If positive post is grounded to the chassis, see 6. Attach clamps to battery and chassis as indicated in Battery Installed in Vehicle steps 5 and 6, or in Battery Outside of Vehicle steps 2 to 5. I'm Jennifer, and I love everything about lighting. FOR THIS REASON, IT IS OF THE UTMOST IMPORTANCE THAT EACH TIME BEFORE USING THE BATTERY CHARGER YOU READ THIS MANUAL AND FOLLOW INSTRUCTIONS EXACTLY. The LCD screen will display the following: Press the alternator check button to start the check. Position AC and clamp cords to reduce risk of damage by hood, door, or moving engine part. SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. The Positive post (marked POS,P, +) usually has a larger diameter than the Negative battery post (marked NEG, N, ). Related Tags everstart maxx battery charger blinking Save my name, email, and website in this browser for the next time I comment. EverStart Battery Charger Maxx BC40BE Instruction manual (8 pages) 3. Like all of our Everstart battery chargers, it uses an integrated microprocessor to control the rate of charging and ensure maximum performance and longevity for your battery. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. The unit may detect that the alternator is out of typical voltage range because someone has added a number of accessory loads on the charging system, thereby increasing current demand from the alternator. Use of improper extension cord could result in a risk of fire and electric shock. To maintain the operating condition and maximize the life of the charger cords, always coil them loosely for storage. Hold the pliers around the wire and twist it around the screw on the battery until its tight. The best way to inspect the battery is by using a voltmeter. Consult the dealer or an experienced radio/TV technician for help. The Everstart Maxx flashlight takes a 12V battery. The red wire should be attached securely to avoid short circuits. If you need to replace the battery, visit an automotive store or online retailer to find a compatible battery. When you're working with me, you're getting someone who truly cares about making your home look and feel its best. Stand as far back from the battery as possible, and do not face battery when making final connection. When the Charging/Charged LED lights solid, the charging process is complete. A: How long does it take to charge an Everstart Maxx alternator? This unit was designed for household use only. Pull by plug rather than cord when unplugging the unit.